Mastering Router-on-a-Stick Configuration: Step-by-Step Guide

Note: Router on a Stick topic Cisco officially announced it is obsolete. we are going to read only for knowledge purposes. In Industry, a router on a Stick configuration is not recommended. 

Unlock the potential of your Cisco router with a router-on-a-stick configuration. Learn how to efficiently segment your network for optimized performance.

Understanding Router-on-a-Stick: Router-on-a-Stick, a technique leveraging VLANs and sub-interfaces, facilitates efficient network segmentation. It enables a single router interface to handle traffic from multiple VLANs, enhancing network efficiency and scalability.

Step-by-Step Configuration Guide:

Select the Main Interface: Access the router's global configuration mode and select the main interface using the

    command: R1(config)# interface Fa0/0.

Remove IP Address: Ensure no IP address is assigned to the main interface with the

    Command: R1(config-if)# no ip address.

Create Sub-Interfaces: Generate sub-interfaces for each VLAN using the     Command: R1(config-if)# interface Fa0/0.10 (replace "10" with the desired VLAN number).

Configure 802.1Q Trunking: Enable 802.1Q trunking on each sub-interface with the     Command: R1(config-if)# encapsulation dot1q [VLAN Number].

Assign IP Address to Sub-Interfaces: Assign IP addresses to each sub-interface using the     Command: R1(config-if)# ip address [IP Address] [Subnet Mask].

Create Sub-Interface for Native Traffic: Establish a sub-interface for native traffic with the     Command: R1(config-if)# interface Fa0/0.99.

Configure 802.1Q Trunking for Native VLAN: Enable 802.1Q trunking and designate the VLAN as native using:     R1(config-if)# encapsulation dot1q 99 native.

Adjust Routing Behavior: Determine routing behavior with the commands:     For classless routing: R1(config)# ip classless.     For classful routing: R1(config)# no ip classless.

Example:

R1(config)# interface Fa0/0 (select the main interface)

R1(config-if)# no ip address (there should not be any IP Address on the main interface)

R1(config-if)# interface Fa0/0.10 (create a sub-interface – the number can be anything)

R1(config-if)# encapsulation dot1q 10 (use 802.1Q trunking; assign to this VLAN #)

R1(config-if)# ip address 172.16.10.1 255.255.255.255 (define the default-gateway IP)

R1(config-if)# interface Fa0/0.99 (create another sub-interface - this one for native traffic)

R1(config-if)# encapsulation dot1q 99 native (802.1Q trunking; VLAN #; and native)

        (NOTE: No IP address unless workstations or management interfaces are on this VLAN)

R1(config)# ip classless (classless routing behavior – default in IOS 11.3+)

R1(config)# no ip classless (classful routing behavior)

Benefits of Router-on-a-Stick Configuration:

Enhanced Network Segmentation: Efficiently segment your network into VLANs, optimizing traffic flow and enhancing security.

Scalability: Easily expand your network without the need for additional physical interfaces, reducing costs and complexity.

Streamlined Management: Centralize network management and configuration, simplifying administrative tasks and improving agility.

Improved Performance: Enhance network performance and bandwidth utilization by routing traffic between VLANs at wire speed.

Mastering router-on-a-stick configuration empowers network administrators to design efficient, scalable, and resilient networks. By following this step-by-step guide, you can leverage VLANs and sub-interfaces to optimize your Cisco router's performance and unlock its full potential.

If found helpful please share likes and comments for more 

Thank you for your valuable time